go-rpio
=======

Native GPIO-Gophers for your Pi!

**Documentation:** [![GoDoc](https://godoc.org/github.com/stianeikeland/go-rpio?status.svg)](https://godoc.org/github.com/stianeikeland/go-rpio)

go-rpio is a Go library for accessing [GPIO](http://elinux.org/Rpi_Low-level_peripherals)-pins
on the [Raspberry Pi](https://en.wikipedia.org/wiki/Raspberry_Pi).

It requires no external c libraries such as
[WiringPI](https://projects.drogon.net/raspberry-pi/wiringpi/) or [bcm2835](http://www.open.com.au/mikem/bcm2835).

There's a tiny bit of additional information over at my [blog](https://blog.eikeland.se/2013/07/30/go-gpio-library-for-raspberry-pi/).

![raspberrypi-blink](http://stianeikeland.files.wordpress.com/2013/07/animated.gif)

## Releases ##
- 1.0.0 - Supports original rpi A/B/B+
- 2.0.0 - Adds support for rpi 2, by @akramer
- 3.0.0 - Adds support for /dev/gpiomem, by @dotdoom
- 4.0.0 - Adds support for PWM and Clock modes, by @Drahoslav7
- 4.1.0 - Adds support for edge detection, by @Drahoslav7
- 4.2.0 - Faster write and toggle of output pins, by @Drahoslav7

## Usage ##

```go
import "github.com/stianeikeland/go-rpio"
```

Open memory range for GPIO access in /dev/mem

```go
err := rpio.Open()
```

Initialize a pin, run basic operations.
Pin refers to the bcm2835 pin, not the physical pin on the raspberry pi header. Pin 10 here is exposed on the pin header as physical pin 19.

```go
pin := rpio.Pin(10)

pin.Output()       // Output mode
pin.High()         // Set pin High
pin.Low()          // Set pin Low
pin.Toggle()       // Toggle pin (Low -> High -> Low)

pin.Input()        // Input mode
res := pin.Read()  // Read state from pin (High / Low)

pin.Mode(rpio.Output)   // Alternative syntax
pin.Write(rpio.High)    // Alternative syntax
```

Pull up/down/off can be set using:

```go
pin.PullUp()
pin.PullDown()
pin.PullOff()

pin.Pull(rpio.PullUp)
```

Unmap memory when done

```go
rpio.Close()
```

Also see example [examples/blinker/blinker.go](examples/blinker/blinker.go)

## Other ##

Currently, it supports basic functionality such as:
- Pin Direction (Input / Output)
- Write (High / Low)
- Read (High / Low)
- Pull (Up / Down / Off)
- PWM (hardware, on supported pins)
- Clock
- Edge detection

It works by memory-mapping the bcm2835 gpio range, and therefore require root/administrative-rights to run.

## Using without root ##

This library can utilize the new [/dev/gpiomem](https://github.com/raspberrypi/linux/pull/1112/files) 
memory range if available. 

You will probably need to upgrade to the latest kernel (or wait for the next raspbian release) if you're missing /dev/gpiomem. You will also need to add a `gpio` group, add your user to the group, and then set up udev rules. I would recommend using [create_gpio_user_permissions.py](https://github.com/waveform80/rpi-gpio/blob/master/create_gpio_user_permissions.py) if you're unsure how to do this.

PWM modes will still require root.